Files (5)

69_POD-Bolt_Setup.stl

STL

259.4 KB

69_POD-Bottom-RIV.stl

STL

70.3 KB

69_POD-Bottom.stl

STL

63.1 KB

69_POD-Capture_Nut.stl

STL

257.2 KB

69_POD-RivNut.stl

STL

250.3 KB

Print plan

Exact totals not supplied

Print setup plan

Useful setup guidance without pretending STL byte size can predict filament, cost, or print time.

5 model files

Material plan

PETG / ASA

Published material guidance; still check heat, UV, load, and printer compatibility.

Starting setup

25% infill

A planning starting point only; wall count, orientation, and geometry often matter more than infill.

Final totals

Confirm in slicer

Choose the needed variant, then slice it for grams, cost, and print time.

Saved setup guidance is used for material, infill, support, and per-file recommendation text; editable numbers are planning estimates only.

Reference shelf

Recommended filament for this print

Product references matched to the published material guidance. Confirm diameter, heat resistance, colour, and printer compatibility.

Referenced item	What to verify	Price & availability
PETG filamentAmazon · Affiliate link	Amazon product page for 1.75 mm PETG; confirm colour, spool size, print temperature, seller, and delivery region.	Check price at Amazon
ASA filamentAmazon · Affiliate link	Amazon product page for 1.75 mm ASA; use an enclosure and suitable ventilation, and confirm seller and regional availability.	Check price at Amazon

Affiliate disclosure: if you buy through an eligible link, 3DPrintedCarPart may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Confirm product specifications, compatibility, seller terms, and vehicle safety before ordering or using anything. Amazon may redirect you to a nearby supported store; otherwise the original Amazon.com page remains available.

Unsure which one fits? Read the automotive filament guide.

Dashboard

69 Mustang Tach POD

0 downloads85 views0 quality score

Print this part

Use the part context as a starting point, then confirm geometry-dependent values in your slicer.

Files

5 hosted model files

STL

Material start

PETG or ASA for durability in a car environment

Saved part guidance

Strength start

20-30% infill for strength and moderate weight

Saved part guidance

Orientation / supports

verify in slicer

Exact totals

Slice for grams + time

Model geometry and final settings determine both

Vehicle exposure

High cabin heat — validate PETG or choose ASA/ABS

Open the STL, 3MF, or OBJ model in your slicer before printing. Exact grams, time, and final support placement come from the actual slice. Test-fit and heat-check the part before installing it in a vehicle.

License & use

CC BY

Commercial use allowed

Attribution required

The file license permits commercial reuse, subject to any applicable attribution or share-alike terms. License status does not verify vehicle fitment, OEM rights, design patents, or safety.

Shared by

3DPrintedCarPart

Verified

Description

This is a POD for a AutoMeter Mini Tach 2 1/16". It includes an area for the upper light fixture and allows the 2 bolts to slide through at the rear..... This requires a 1/8" Foam to be added to the the part that goes around the column, this is to prevent scratching and should also allow it to be fixed with out much movement I used https://www.amazon.com/dp/B07RYW3Q46 I have added 3 versions: RivNUT - This version you use a 10-24 rivnut into the hole at the bottom of the top half and glue it in...It fits without the glue and seems pretty snug but glue it in just to be safe. I use a 3/4" bolt/screw Bolt Setup - This one is made so you can use a bolt and nut to hold it together Capture Nut - Allows you to use a 1/4" bolt and and insert a nut into the back of the bezel. Nut should be flat to each side to be centered properly ***bottom-riv just has a smaller hole as i found the rivnut bolt was smaller but either can be used.