Air-Vent Mount for Ford Fusion(and alike) Cars w/ Wireless Phone charger Ball joint - image

Files (1)

carventmountwithballjoint.stl

STL

1.2 MB

Print plan

Exact totals not supplied

Print setup plan

Useful setup guidance without pretending STL byte size can predict filament, cost, or print time.

1 model file

Material plan

PETG / ASA

Published material guidance; still check heat, UV, load, and printer compatibility.

Starting setup

25% infill

A planning starting point only; wall count, orientation, and geometry often matter more than infill.

Final totals

Confirm in slicer

Slice the selected model with your final material, orientation, walls, and supports.

Saved setup guidance is used for material, infill, support, and per-file recommendation text; editable numbers are planning estimates only.

Reference shelf

Recommended filament for this print

Product references matched to the published material guidance. Confirm diameter, heat resistance, colour, and printer compatibility.

Referenced item	What to verify	Price & availability
PETG filamentAmazon · Affiliate link	Amazon product page for 1.75 mm PETG; confirm colour, spool size, print temperature, seller, and delivery region.	Check price at Amazon
ASA filamentAmazon · Affiliate link	Amazon product page for 1.75 mm ASA; use an enclosure and suitable ventilation, and confirm seller and regional availability.	Check price at Amazon

Affiliate disclosure: if you buy through an eligible link, 3DPrintedCarPart may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Confirm product specifications, compatibility, seller terms, and vehicle safety before ordering or using anything. Amazon may redirect you to a nearby supported store; otherwise the original Amazon.com page remains available.

Unsure which one fits? Read the automotive filament guide.

Phone Mounts

Air-Vent Mount for Ford Fusion(and alike) Cars w/ Wireless Phone charger Ball joint

0 downloads83 views0 quality score

Print this part

Use the part context as a starting point, then confirm geometry-dependent values in your slicer.

Files

1 hosted model file

STL

Material start

PETG or ASA for durability and heat resistance

Saved part guidance

Strength start

20-30% infill for strength and minimal weight

Saved part guidance

Orientation / supports

verify in slicer

Exact totals

Slice for grams + time

Model geometry and final settings determine both

Vehicle exposure

High cabin heat — validate PETG or choose ASA/ABS

Open the STL, 3MF, or OBJ model in your slicer before printing. Exact grams, time, and final support placement come from the actual slice. Test-fit and heat-check the part before installing it in a vehicle.

License & use

CC BY

Commercial use allowed

Attribution required

The file license permits commercial reuse, subject to any applicable attribution or share-alike terms. License status does not verify vehicle fitment, OEM rights, design patents, or safety.

Shared by

3DPrintedCarPart

Verified

Description

I needed the ability to mount my Windshield Wireless Qi Phone Charger to my Car's Air-vents, and everything I could find already either didn't seem strong enough, or wouldn't fit my style car vent. I made my own mount instead, and it's extremely strong, sturdy, robust, and simple to print. My Original Windshield mount's connector is a press-fit design with a 17 mm ball on the end, and it kept slipping out of the slot, causing my phone to come crashing down while I was driving (not ok). Not only that, but since I drive a black car in the South, the phone would often overheat and pause wireless charging if the AC hadn't been running long enough which was quite annoying. This design uses my Air-Vent Mount (look at Remix Sources for that) where I added a ~30mm extension and a 17mm Ball on the end to fit the original wireless charger. Now, my phone mounts directly to the air-vent, where it stays nice and cool, and Doesn't fall down:) If your Wireless phone charger is similar to this one: https://www.aliexpress.com/item/Qi-Wireless-Car-Charger-Mount-Phone-Holder-for-iPhone-8-Plus-X-10-8W-Fast-Wireless/32847574913.html Then it should work with yours. It uses a 17 mm ball joint design for the pivot, and is a easy swap from OEM windshield mount to the printed one.