Door handle (inner) Honda Accord IV 1989-1993 (CB-3, CB-7) - image

Files (2)

Case_Door_Handle_Honda_Accord_1989-1993.stl

STL

531.8 KB

Door_Handle_Honda_Accord_1989-1993.stl

STL

140.9 KB

Print plan

Exact totals not supplied

Print setup plan

Useful setup guidance without pretending STL byte size can predict filament, cost, or print time.

2 model files

Material plan

PETG / ASA

Published material guidance; still check heat, UV, load, and printer compatibility.

Starting setup

25% infill

A planning starting point only; wall count, orientation, and geometry often matter more than infill.

Final totals

Confirm in slicer

Slice the selected model with your final material, orientation, walls, and supports.

Saved setup guidance is used for material, infill, support, and per-file recommendation text; editable numbers are planning estimates only.

Reference shelf

Recommended filament for this print

Product references matched to the published material guidance. Confirm diameter, heat resistance, colour, and printer compatibility.

Referenced item	What to verify	Price & availability
PETG filamentAmazon · Affiliate link	Amazon product page for 1.75 mm PETG; confirm colour, spool size, print temperature, seller, and delivery region.	Check price at Amazon
ASA filamentAmazon · Affiliate link	Amazon product page for 1.75 mm ASA; use an enclosure and suitable ventilation, and confirm seller and regional availability.	Check price at Amazon

Affiliate disclosure: if you buy through an eligible link, 3DPrintedCarPart may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Confirm product specifications, compatibility, seller terms, and vehicle safety before ordering or using anything. Amazon may redirect you to a nearby supported store; otherwise the original Amazon.com page remains available.

Unsure which one fits? Read the automotive filament guide.

Door Handles

Door handle (inner) Honda Accord IV 1989-1993 (CB-3, CB-7)

3 downloads170 views0 quality score

Print this part

Use the part context as a starting point, then confirm geometry-dependent values in your slicer.

Files

2 hosted model files

STL

Material start

PETG or ASA for durability and heat resistance

Saved part guidance

Strength start

20-30% infill for a balance between strength and weight

Saved part guidance

Orientation / supports

verify in slicer

Exact totals

Slice for grams + time

Model geometry and final settings determine both

Vehicle exposure

Cabin/interior use; avoid high-heat zones

Open the STL, 3MF, or OBJ model in your slicer before printing. Exact grams, time, and final support placement come from the actual slice. Test-fit and heat-check the part before installing it in a vehicle.

License & use

CC BY

Commercial use allowed

Attribution required

The file license permits commercial reuse, subject to any applicable attribution or share-alike terms. License status does not verify vehicle fitment, OEM rights, design patents, or safety.

Shared by

3DPrintedCarPart

Verified

Description

В моей стране моделей Honda Accord 1989-1993 (CB3, CB7) очень мало и найти какую либо деталь на них является большой проблемой. Вот так я так и не смог найти ручку двери с корпусом. Корпус и ручку нашел на просторах интернета, всё по отдельности и они были для других моделей. Немного подправил под модель Honda Accord 1989-1993 (CB3, CB7) Эта модель для правой стороны автомобиля. Для левой стороны просто сделайте зеркальное положение In my country, there are very few Honda Accord 1989-1993 (CB3, CB7) models and finding any part on them is a big problem. That's how I could not find the door handle with the body. I found the body and handle on the Internet, all separately and they were for other models. Slightly tweaked for Honda Accord 1989-1993 (CB3, CB7) This model is for the right side of the car. For the left side, just make a mirror position PS 21.02.2022 Fixed hole position and replaced files.