Files (1)

Fiat Cup Holder.stl

STL

4.4 MB

Print plan

Exact totals not supplied

Print setup plan

Useful setup guidance without pretending STL byte size can predict filament, cost, or print time.

1 model file

Material plan

PETG / ASA

Published material guidance; still check heat, UV, load, and printer compatibility.

Starting setup

65% infill

A planning starting point only; wall count, orientation, and geometry often matter more than infill.

Final totals

Confirm in slicer

Slice the selected model with your final material, orientation, walls, and supports.

Saved setup guidance is used for material, infill, support, and per-file recommendation text; editable numbers are planning estimates only.

Reference shelf

Recommended filament for this print

Product references matched to the published material guidance. Confirm diameter, heat resistance, colour, and printer compatibility.

Referenced item	What to verify	Price & availability
PETG filamentAmazon · Affiliate link	Amazon product page for 1.75 mm PETG; confirm colour, spool size, print temperature, seller, and delivery region.	Check price at Amazon
ASA filamentAmazon · Affiliate link	Amazon product page for 1.75 mm ASA; use an enclosure and suitable ventilation, and confirm seller and regional availability.	Check price at Amazon

Affiliate disclosure: if you buy through an eligible link, 3DPrintedCarPart may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Confirm product specifications, compatibility, seller terms, and vehicle safety before ordering or using anything. Amazon may redirect you to a nearby supported store; otherwise the original Amazon.com page remains available.

Unsure which one fits? Read the automotive filament guide.

Fiat 500 Cup Holder Phone Stand

0 downloads10 views0 quality score

Print this part

Use the part context as a starting point, then confirm geometry-dependent values in your slicer.

Files

1 hosted model file

STL

Material start

PETG or ASA for durability and heat resistance

Saved part guidance

Strength start

65% or higher for strength and stability

Saved part guidance

Orientation / supports

supports unlikely

Exact totals

Slice for grams + time

Model geometry and final settings determine both

Vehicle exposure

Cabin/interior use; avoid high-heat zones

Open the STL, 3MF, or OBJ model in your slicer before printing. Exact grams, time, and final support placement come from the actual slice. Test-fit and heat-check the part before installing it in a vehicle.

License & use

CC BY-SA

Commercial use allowed

Attribution required

Safety/IP review

The file license permits commercial reuse, subject to any applicable attribution or share-alike terms. License status does not verify vehicle fitment, OEM rights, design patents, or safety.

Shared by

3DPrintedCarPart

Verified

Description

I designed this cup holder insert to make better use of holding my phone, sun glasses and garage door opener. It does take up two cup holder spaces. See the photos to make sure it fits your model Fiat 500, I included an original press photo which shows the unusual cup holder this is made for. Fiat Logo has been traced and embossed into the model on the top and there is a through-the-model pathway designed to route the power cord cleanly from the cigarette lighter to the phone holder. The phone post is designed to hold a self-closing phone holder like this one that I purchased on amazon. It has a ball on the end of the post designed to couple with most phone holders. The diameter of the ball is 18mm. The second option allows the phone to be further away from the gear selector area, but it does hover over the parking brake - so it would be in the way if you needed to use the parking brake. I like this design because it's easier to get my iPhone into the cradle and I can still use the parking brake, it's just not quite as accessible with a phone hovering over it. If you are concerned about the parking brake in the way, I do have another model that mounts in the TomTom port here: https://www.printables.com/model/860029-fiat-500-tomtom-phone-stand Phone holder I purchased (but there are many others like it): https://www.amazon.com/dp/B0BL1S9LFJ?psc=1&ref=ppx_yo2ov_dt_b_product_details Garage Door opener slot is designed for a chamberlain/lift master garage door opener. Sunglass holder should fit most sunglasses (Maui Jims fit great here) No supports are needed, use a brim or a raft if you have print bed adhesion issues. Recommend Infill 65% or more (I print this part at 70%).