Kia Niro 2016 to 2019 mobile holder mount - image

Files (2)

FLOVEME_gravity_holder_adapter.stl

STL

978.2 KB

Kia_Niro_phone_holder_v3.stl

STL

223.8 KB

Print plan

Exact totals not supplied

Print setup plan

Useful setup guidance without pretending STL byte size can predict filament, cost, or print time.

2 model files

Material plan

PETG / ABS

Published material guidance; still check heat, UV, load, and printer compatibility.

Starting setup

25% infill

A planning starting point only; wall count, orientation, and geometry often matter more than infill.

Final totals

Confirm in slicer

Slice the selected model with your final material, orientation, walls, and supports.

Saved setup guidance is used for material, infill, support, and per-file recommendation text; editable numbers are planning estimates only.

Reference shelf

Recommended filament for this print

Product references matched to the published material guidance. Confirm diameter, heat resistance, colour, and printer compatibility.

Referenced item	What to verify	Price & availability
PETG filamentAmazon · Affiliate link	Amazon product page for 1.75 mm PETG; confirm colour, spool size, print temperature, seller, and delivery region.	Check price at Amazon
ABS filamentAmazon · Affiliate link	Amazon product page for 1.75 mm ABS; use an enclosure and suitable ventilation, and verify temperature requirements and seller.	Check price at Amazon

Affiliate disclosure: if you buy through an eligible link, 3DPrintedCarPart may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Confirm product specifications, compatibility, seller terms, and vehicle safety before ordering or using anything. Amazon may redirect you to a nearby supported store; otherwise the original Amazon.com page remains available.

Unsure which one fits? Read the automotive filament guide.

Phone Mounts

Kia Niro 2016 to 2019 mobile holder mount

2 downloads411 views0 quality score

Print this part

Use the part context as a starting point, then confirm geometry-dependent values in your slicer.

Files

2 hosted model files

STL

Material start

PETG or ABS

Saved part guidance

Strength start

20-30% infill for durability, with 2-3 perimeter walls

Saved part guidance

Orientation / supports

supports likely, verify in slicer

Exact totals

Slice for grams + time

Model geometry and final settings determine both

Vehicle exposure

High cabin heat — validate PETG or choose ASA/ABS

Open the STL, 3MF, or OBJ model in your slicer before printing. Exact grams, time, and final support placement come from the actual slice. Test-fit and heat-check the part before installing it in a vehicle.

License & use

CC BY

Commercial use allowed

Attribution required

The file license permits commercial reuse, subject to any applicable attribution or share-alike terms. License status does not verify vehicle fitment, OEM rights, design patents, or safety.

Shared by

3DPrintedCarPart

Verified

Description

This is a mobile phone mount for the 2016 to 2019 (or more) Kia Niro (left hand drive). It is held in place by tabs 2 print-in-place tabs built into the design. I designed the mount to minimize obstruction the vent as much as possible which unfortunately resulted in the need for supports during printing. Printing... This is printed on its side left with supports enabled. Print direction is important as to orientate the fixing-tap layer lines correctly. Use PETG or perhaps ABS - but not PLA, it will melt on the hot days. I have used PETG and that seems to work OK so far - need to wait for summer though. My example was printed using a 0.8mm nozzle on an Ender 3. The support face look a bit ugly as a result of the larger nozzle. To install this you will need a spudger to open up the tiny gap between the dashpad and vent face and CAREFULLY wiggle the holder in place - repeat for the lower tab. The mount has holes which allows general attachment of a mobile "clamp". I myself use the FLOVEME Gravity Car Phone Holder which i purchase from Aliexpress. The FLOVEME adapter included here will fit inplace of the original vent holder. I have 2 cars using the FLOVEME and have had no problems over 5 years - they work well. I can create a mirror version of this for the right hand drive folk if required - send me a PM.