Radenso DS1 Screen Mount for Tesla Model 3/Y - image

Files (2)

Radenso_DS1_Telsa_Mount_v2.8.stl

STL

68.7 KB

Radenso_DS1_Telsa_Mount_v2.9.2.stl

STL

63.9 KB

Print plan

Exact totals not supplied

Print setup plan

Useful setup guidance without pretending STL byte size can predict filament, cost, or print time.

2 model files

Material plan

PETG / ASA

Published material guidance; still check heat, UV, load, and printer compatibility.

Starting setup

25% infill

A planning starting point only; wall count, orientation, and geometry often matter more than infill.

Final totals

Confirm in slicer

Choose the needed variant, then slice it for grams, cost, and print time.

Saved setup guidance is used for material, infill, support, and per-file recommendation text; editable numbers are planning estimates only.

Reference shelf

Recommended filament for this print

Product references matched to the published material guidance. Confirm diameter, heat resistance, colour, and printer compatibility.

Referenced item	What to verify	Price & availability
PETG filamentAmazon · Affiliate link	Amazon product page for 1.75 mm PETG; confirm colour, spool size, print temperature, seller, and delivery region.	Check price at Amazon
ASA filamentAmazon · Affiliate link	Amazon product page for 1.75 mm ASA; use an enclosure and suitable ventilation, and confirm seller and regional availability.	Check price at Amazon

Affiliate disclosure: if you buy through an eligible link, 3DPrintedCarPart may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Confirm product specifications, compatibility, seller terms, and vehicle safety before ordering or using anything. Amazon may redirect you to a nearby supported store; otherwise the original Amazon.com page remains available.

Unsure which one fits? Read the automotive filament guide.

Phone Mounts

Radenso DS1 Screen Mount for Tesla Model 3/Y

0 downloads49 views0 quality score

Print this part

Use the part context as a starting point, then confirm geometry-dependent values in your slicer.

Files

2 hosted model files

STL

Material start

PETG or ASA for durability in a car environment

Saved part guidance

Strength start

20-30% infill for a balance between weight and strength

Saved part guidance

Orientation / supports

verify in slicer

Exact totals

Slice for grams + time

Model geometry and final settings determine both

Vehicle exposure

High cabin heat — validate PETG or choose ASA/ABS

Open the STL, 3MF, or OBJ model in your slicer before printing. Exact grams, time, and final support placement come from the actual slice. Test-fit and heat-check the part before installing it in a vehicle.

License & use

CC BY

Commercial use allowed

Attribution required

The file license permits commercial reuse, subject to any applicable attribution or share-alike terms. License status does not verify vehicle fitment, OEM rights, design patents, or safety.

Shared by

3DPrintedCarPart

Verified

Description

Radenso DS1 Tesla Screen Mount for Model 3/Y I tried to get it near as flush with the screen as I could with out it looking oddly out of place on the backside of the mount. When you purchase the Radenso DS1, it comes with a suction-cup mount that uses a magnet to lock the mounting system in place for the detector. If you notice on one side of the mount, there is a rectangular "tube". You can easily unscrew the magnetic from the suction-cup, take the magnet out and that rectangular "tube" snugly fits the stock magnet. Giving this mount also the ability to be magnetic as well. It does fit snug around the screen, but just snug enough to not cause any damage and still remain in place (most of my revisions were getting this part right). Shout out to @b00st3d, his V1G2 mount was what gave me the idea for this, as originally I was going to go with the V1G2 (https://www.thingiverse.com/thing:4914573). In a future revision I plan on adding some small cable guides to have the cable going towards the passenger side of the car. Also, from what I hear this will be very similar (if not the same) mounting system for the Radenso Theia:) Version History * 2.9.2 - I wanted some better magnet action, so I upgraded the magnet slight. 2.9.2 uses a N52 19.5x9.53x6.35mm (I bought mine from TotalElement.com) * 2.8 - Noticed due to the tilt of the screen the radar detector pointed down instead of straight, this is corrected in 2.8. * 2.5 - Release.