Files (7)

skoda_camera_pillar.stl

STL

513.9 KB

skoda_camera_vent_clamp.stl

STL

83.7 KB

skoda_camera_vent_bracket.stl

STL

176.6 KB

skoda_camera_lower_hinge.stl

STL

176.6 KB

skoda_camera_hinge_plate.stl

STL

180.9 KB

skoda_camera_retainer.stl

STL

371.5 KB

skoda_camera_mount.stl

STL

489.3 KB

Print guidance estimate

Slicer data required

Print cost & setup estimate

Setup guidance plus saved or slicer-confirmed filament, cost, and time. Model file size is never treated as printable volume.

7 model files

Recommended kit

Slice required

Slice the required model files; source file size is not printable volume.

Material cost

Slice required

Use the slicer's filament total; STL/3MF byte size is not a cost input.

Print time

Slice required

Slice with the recommended material, infill, orientation, and supports.

STL file	Role	Source size	PETG / ASA 20%	PETG / ASA 25%	100% solid	Recommendation
skoda_camera_pillar.stl	Printable file	513.9 KB STL	Slice file	Slice file	Slice file	Ensure proper orientation for optimal printing and minimal supports.
skoda_camera_vent_clamp.stl	Printable file	83.7 KB STL	Slice file	Slice file	Slice file	Ensure proper orientation for optimal printing and minimal supports.
skoda_camera_vent_bracket.stl	Mount / bracket	176.6 KB STL	Slice file	Slice file	Slice file	Ensure proper orientation for optimal printing and minimal supports.
skoda_camera_lower_hinge.stl	Printable file	176.6 KB STL	Slice file	Slice file	Slice file	Ensure proper orientation for optimal printing and minimal supports.
skoda_camera_hinge_plate.stl	Printable file	180.9 KB STL	Slice file	Slice file	Slice file	Ensure proper orientation for optimal printing and minimal supports.
skoda_camera_retainer.stl	Printable file	371.5 KB STL	Slice file	Slice file	Slice file	Ensure proper orientation for optimal printing and minimal supports.
skoda_camera_mount.stl	Mount / bracket	489.3 KB STL	Slice file	Slice file	Slice file	Ensure proper orientation for optimal printing and minimal supports.

Saved setup guidance is used for material, infill, support, and per-file recommendation text; editable numbers are planning estimates only.

Dashboard

Skoda Fabia Dashcam holder

0 downloads70 views0 quality score

Print this part

Check the available model and saved setup details before opening your slicer.

Files

7 hosted model files

STL

Material

PETG or ASA

Print time

Slice to calculate

Filament

Slice to calculate

Supports

verify in slicer

Infill

20-30% infill with 1.2-1.6 mm walls

Difficulty

Not rated — inspect geometry

Vehicle heat

Cabin/interior use; avoid high-heat zones

Open the STL, 3MF, or OBJ model in your slicer before printing. Confirm orientation, supports, print time, filament use, and printer compatibility. Test-fit before installing it in a vehicle.

License & use

CC BY

Commercial use allowed

Attribution required

The file license permits commercial reuse, subject to any applicable attribution or share-alike terms. License status does not verify vehicle fitment, OEM rights, design patents, or safety.

Shared by

3DPrintedCarPart

Verified

Description

Getting tired of cameras falling off the sucker mounts and don't want to use adhesive pads so developed this bracket. Currently only fits a Skoda Fabia but could easily be adapted for other vehicles as each section screws together. These vehicle cameras are cheap but don't last all that long, the style is popular at the moment on eBay for around £20 and works well. If I have to change cameras in the future only the top plate needs to be redesigned. Bracket allows access to power button, connector and micro sd card. Some stl's are not orientated properly for printing, no time to correct at present but hopefully it should be fairly obvious. Contact me if in doubt.