Files (2)
Published material guidance; still check heat, UV, load, and printer compatibility.
A planning starting point only; wall count, orientation, and geometry often matter more than infill.
Slice the selected model with your final material, orientation, walls, and supports.
Saved setup guidance is used for material, infill, support, and per-file recommendation text; editable numbers are planning estimates only.
Reference shelf
Recommended filament for this print
Product references matched to the published material guidance. Confirm diameter, heat resistance, colour, and printer compatibility.
| Referenced item | What to verify | Price & availability |
|---|---|---|
| ASA filamentAmazon · Affiliate link | Amazon product page for 1.75 mm ASA; use an enclosure and suitable ventilation, and confirm seller and regional availability. | Check price at Amazon |
| ABS filamentAmazon · Affiliate link | Amazon product page for 1.75 mm ABS; use an enclosure and suitable ventilation, and verify temperature requirements and seller. | Check price at Amazon |
Affiliate disclosure: if you buy through an eligible link, 3DPrintedCarPart may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Confirm product specifications, compatibility, seller terms, and vehicle safety before ordering or using anything. Amazon may redirect you to a nearby supported store; otherwise the original Amazon.com page remains available.
Unsure which one fits? Read the automotive filament guide.
Lexus IS220/IS250/IS350 phone holder + Qi wireless charging
Print this part
Use the part context as a starting point, then confirm geometry-dependent values in your slicer.
Files
2 hosted model files
STL
Material start
ABS or ASA for durability in a hot car environment
Saved part guidance
Strength start
20-30% infill for a balance between strength and weight
Saved part guidance
Orientation / supports
verify in slicer
Exact totals
Slice for grams + time
Model geometry and final settings determine both
Vehicle exposure
Windshield/dash heat — validate after a parked-car soak
Open the STL, 3MF, or OBJ model in your slicer before printing. Exact grams, time, and final support placement come from the actual slice. Test-fit and heat-check the part before installing it in a vehicle.
License & use
The file license permits commercial reuse, subject to any applicable attribution or share-alike terms. License status does not verify vehicle fitment, OEM rights, design patents, or safety.
Shared by
3DPrintedCarPartDescription
This is a dash phone holder with a built-in Qi charger for a Lexus IS220/IS250/IS350. It's a springy compliant mechanism which clicks into your dash without damaging anything, and is easily removable with no traces! It's strong and supportive. I added a piece of transparent tape to the vent plastic where the mount rubs so it doesn't leave any scratches. The aim of the grille is compromised slightly up/down, but left/right is unaffected. It comes in 2 parts - the dash part and the phone part. The 2 parts either screw together with M3 screws, or glue together. The phone part is designed for a Xiaomi Mix 2S. The phone is 75mm wide and is a nice tight click-fit with a slight cut out for the on/off button. It's designed for slight flex with ABS (don't even think about PLA in a hot car!). If you need it for your phone, I'm happy to modify it if you throw me a tip:). Just measure the width, where your buttons are, and drop me a PM. If you want to use wireless charging, you'll need to do a bit of soldering. - The Qi charging module is this one from AliExpress: https://www.aliexpress.com/item/New-Qi-Fast-Wireless-Charger-PCBA-Circuit-Board-Transmitter-Module-Coil-Charging-High-Quality-Qi-Wireless/32951758605.html If you're buying this module, make sure it comes with the 9v input components (mine didn't!) - this will allow the full 10w fast charging. The wireless disc is secured with hot glue but would recommend epoxy if you're in a hot climate. You'll also need a step-down buck converter to take your 12v car voltage down to either 5v USB input, or 9v fast charging input depending on which you want. - I recommend this one as it has plenty of head room for fast charging (supports 30w without any additional cooling) https://www.aliexpress.com/item/Automatic-Step-Up-Down-DC-Power-Supply-AT30-Converter-Buck-Boost-Module-Replace-XL6009-4-30V/32952614571.html - I tested it with this 'weaker' LM2596 module, but it does get quite hot. It only officially supports 10w without external cooling: https://www.aliexpress.com/item/new-1pcs-lot-LM2596S-LM2596-LM2596-ADJ-DC-DC-Step-down-module-5V-12V-24V-adjustable/32828600888.html I haven't yet figured out where to take the 12v from, but I'm sure there's a nice beefy 12v supply behind the nav screen - I'll be doing this next and will update the pics when I find one.
Originally published on thingiverse.com by Aivaras (AS_Motion_Lab) · License: CC BY
Share whether this print actually fits a real car. Installed photos and material notes make the catalog more trustworthy.
Related Parts
Most specific car + model + year + category matches first, with popular parts mixed in.
1/2U Cell phone holder
14.5mm ball phone mount for 3rd Gen Toyota Tacoma
EG Civic accessory button phone holder
17 Civic Phone Rest
2013-2018 Ram 1500 Dash Mount for Cell Phones
2004-2010 Hyundai Sonata Headlight Dust cap
Hyundai
