MX-5 NB FL mounting for licence plate mazda miata - image

Files (2)

NRSD_V2.stl

STL

96.9 KB

NRSD_V2.stp

STP

166.8 KB

Print plan

Exact totals not supplied

Print setup plan

Useful setup guidance without pretending STL byte size can predict filament, cost, or print time.

2 model files

Material plan

PETG / ASA

Published material guidance; still check heat, UV, load, and printer compatibility.

Starting setup

25% infill

A planning starting point only; wall count, orientation, and geometry often matter more than infill.

Final totals

Confirm in slicer

Choose the needed variant, then slice it for grams, cost, and print time.

Saved setup guidance is used for material, infill, support, and per-file recommendation text; editable numbers are planning estimates only.

Reference shelf

Recommended filament for this print

Product references matched to the published material guidance. Confirm diameter, heat resistance, colour, and printer compatibility.

Referenced item	What to verify	Price & availability
PETG filamentAmazon · Affiliate link	Amazon product page for 1.75 mm PETG; confirm colour, spool size, print temperature, seller, and delivery region.	Check price at Amazon
ASA filamentAmazon · Affiliate link	Amazon product page for 1.75 mm ASA; use an enclosure and suitable ventilation, and confirm seller and regional availability.	Check price at Amazon

Affiliate disclosure: if you buy through an eligible link, 3DPrintedCarPart may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Confirm product specifications, compatibility, seller terms, and vehicle safety before ordering or using anything. Amazon may redirect you to a nearby supported store; otherwise the original Amazon.com page remains available.

Unsure which one fits? Read the automotive filament guide.

Rear Bumper

MX-5 NB FL mounting for licence plate mazda miata

0 downloads64 views0 quality score

Print this part

Use the part context as a starting point, then confirm geometry-dependent values in your slicer.

Files

2 hosted model files

STL + STP

Material start

PETG or ASA for outdoor durability

Saved part guidance

Strength start

20-30% infill for strength and minimal weight

Saved part guidance

Orientation / supports

verify in slicer

Exact totals

Slice for grams + time

Model geometry and final settings determine both

Vehicle exposure

UV/weather exposure — ASA is the starting point

Open the STL, 3MF, or OBJ model in your slicer before printing. Exact grams, time, and final support placement come from the actual slice. Test-fit and heat-check the part before installing it in a vehicle.

License & use

CC BY

Commercial use allowed

Attribution required

The file license permits commercial reuse, subject to any applicable attribution or share-alike terms. License status does not verify vehicle fitment, OEM rights, design patents, or safety.

Shared by

3DPrintedCarPart

Verified

Description

Hier ein Kennzeichenhalter für den MX-5 NB FL. Ich denke, der passt auch beim NB. Es gibt zwei Möglichkeiten um den Halter zu montieren. 1. Per Schraube durch die Stoßstange. 2. Per Magnet. Hierfür könnt ihr Magnten mit einem Durchmesser von 15mm und einer Höhe von 5mm in die Vertiefungen einkleben. Danach klebt ihr im Inneren der Stoßstange ebenfalls die Magneten ein. Dann sollte der Halter per Magnet halten und wieder entnehmbar sein. Diese Variante habe ich aber noch nicht getestet. Freue mich aber über ein Feedback. Falls ihr den Halter modifizieren wollt, könnt ihr das gerne tun. Für diesen Fall habe ich auch eine STP mit hochgeladen:) Material: PLA Düse: 0,4mm Wandstärke: 2 Linien Schichtstärke: 0,3mm Füllung: 15% Support: Ja (für die Bohrungen) English: Here is a license plate holder for the MX-5 NB FL. I think it also fits to the NB. There are two ways to mount the holder. 1. by screw through the bumper. 2. by magnet. For this you can glue magnets with a diameter of 15mm and a height of 5mm in the recesses. Then glue the magnets inside the bumper as well. After that the holder should hold by magnet and be removable again. I have not tested this versionyet. But I am glad about a feedback. material: PLA nozzle: 0,4mm wall thickness: 2 lines linethickness: 0,3mm infill: 15% support: yes (for the holes) Translated with www.DeepL.com/Translator (free version).