Tesla Model 3 2024 Highland Organizer for Center Console - image

Files (1)

organizer.stl

STL

47.5 KB

Print plan

Exact totals not supplied

Print setup plan

Useful setup guidance without pretending STL byte size can predict filament, cost, or print time.

1 model file

Material plan

PETG

Published material guidance; still check heat, UV, load, and printer compatibility.

Starting setup

25% infill

A planning starting point only; wall count, orientation, and geometry often matter more than infill.

Final totals

Confirm in slicer

Slice the selected model with your final material, orientation, walls, and supports.

Saved setup guidance is used for material, infill, support, and per-file recommendation text; editable numbers are planning estimates only.

Reference shelf

Recommended filament for this print

Product references matched to the published material guidance. Confirm diameter, heat resistance, colour, and printer compatibility.

Referenced item	What to verify	Price & availability
PETG filamentAmazon · Affiliate link	Amazon product page for 1.75 mm PETG; confirm colour, spool size, print temperature, seller, and delivery region.	Check price at Amazon

Affiliate disclosure: if you buy through an eligible link, 3DPrintedCarPart may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Confirm product specifications, compatibility, seller terms, and vehicle safety before ordering or using anything. Amazon may redirect you to a nearby supported store; otherwise the original Amazon.com page remains available.

Unsure which one fits? Read the automotive filament guide.

Tesla Model 3 2024 Highland Organizer for Center Console

0 downloads14 views0 quality score

Print this part

Use the part context as a starting point, then confirm geometry-dependent values in your slicer.

Files

1 hosted model file

STL

Material start

PETG

Saved part guidance

Strength start

20-30% infill for durability, with 1.2-1.6mm walls

Saved part guidance

Orientation / supports

supports likely, verify in slicer

Exact totals

Slice for grams + time

Model geometry and final settings determine both

Vehicle exposure

Cabin/interior use; avoid high-heat zones

Open the STL, 3MF, or OBJ model in your slicer before printing. Exact grams, time, and final support placement come from the actual slice. Test-fit and heat-check the part before installing it in a vehicle.

License & use

CC BY-SA

Commercial use allowed

Attribution required

The file license permits commercial reuse, subject to any applicable attribution or share-alike terms. License status does not verify vehicle fitment, OEM rights, design patents, or safety.

Shared by

3DPrintedCarPart

Verified

Description

*english below* Ein Organizer für die Mittelkonsole des Tesla Model 3 2024 Highland Das Model beinhaltet ein mal den Organizer selbst und ein Münz-/Kartenfach. Diese zwei Teile können separat oder auch zusammen mit ein mal gedruckt werden. Ich habe den Boden des Models noch mit Moosgummi und Filz aus dem Baumarkt ausgekleidet. Unter die seitlichen Überhänge habe ich ebenfalls etwas Filz geklebt, damit es besser gleitet. Das gleiche hab ich mit den sichtbaren Seiten des Münz-/Kartenfaches gemacht, damit es schöner aussieht. Druckempfehlungen: - Material: PETG (oder wärmebeständiges PLA) - Line Height: 0.2mm - mit Brim (damit die Ecken nicht abheben) - mit Supports _________________________________________________ An organizer for the center console of the Tesla Model 3 2024 Highland The model includes the organizer itself and a coin/card compartment. These two parts can be printed separately or together. I covered the bottom of the model with foam rubber and felt from the hardware store. I also glued some felt under the side overhangs so that it slides better. I did the same with the visible sides of the coin/card compartment to make it look nicer. Printing recommendations: - Material: PETG (or heat resistant PLA) - Line Height: 0.2mm - with brim (to prevent the corners from lifting) - with supports