100 Series Landcruiser Light Weight Roof Rack Mount - image

Files (2)

RoofRackLight.3mf

3MF

16.8 KB

RoofRackLight.stl

STL

334.7 KB

Print plan

Exact totals not supplied

Print setup plan

Useful setup guidance without pretending STL byte size can predict filament, cost, or print time.

2 model files

Material plan

PETG / ASA

Published material guidance; still check heat, UV, load, and printer compatibility.

Starting setup

50% infill

A planning starting point only; wall count, orientation, and geometry often matter more than infill.

Final totals

Confirm in slicer

Choose the needed variant, then slice it for grams, cost, and print time.

Saved setup guidance is used for material, infill, support, and per-file recommendation text; editable numbers are planning estimates only.

Reference shelf

Recommended filament for this print

Product references matched to the published material guidance. Confirm diameter, heat resistance, colour, and printer compatibility.

Referenced item	What to verify	Price & availability
PETG filamentAmazon · Affiliate link	Amazon product page for 1.75 mm PETG; confirm colour, spool size, print temperature, seller, and delivery region.	Check price at Amazon
ASA filamentAmazon · Affiliate link	Amazon product page for 1.75 mm ASA; use an enclosure and suitable ventilation, and confirm seller and regional availability.	Check price at Amazon

Affiliate disclosure: if you buy through an eligible link, 3DPrintedCarPart may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Confirm product specifications, compatibility, seller terms, and vehicle safety before ordering or using anything. Amazon may redirect you to a nearby supported store; otherwise the original Amazon.com page remains available.

Unsure which one fits? Read the automotive filament guide.

Exterior

100 Series Landcruiser Light Weight Roof Rack Mount

0 downloads1.5K views0 quality score

Print this part

Use the part context as a starting point, then confirm geometry-dependent values in your slicer.

Files

2 hosted model files

STL + 3MF

Material start

PETG or ASA for durability in outdoor conditions

Saved part guidance

Strength start

50% infill with 8-layer walls for strength

Saved part guidance

Orientation / supports

verify in slicer

Exact totals

Slice for grams + time

Model geometry and final settings determine both

Vehicle exposure

UV/weather exposure — ASA is the starting point

Open the STL, 3MF, or OBJ model in your slicer before printing. Exact grams, time, and final support placement come from the actual slice. Test-fit and heat-check the part before installing it in a vehicle.

License & use

CC BY

Commercial use allowed

Attribution required

Safety/IP review

The file license permits commercial reuse, subject to any applicable attribution or share-alike terms. License status does not verify vehicle fitment, OEM rights, design patents, or safety.

Shared by

3DPrintedCarPart

Verified

Description

Please Note: I have designed this bracket for the roof of my 100 Series Landcruiser purely just to mount a solar panel. If you use this to carry any weight, then you do so at your own risk my dudes! I print these brackets using 40mm/s with 50% infill and 8layer walls. This seems to give me the right strength. I print in PETG however I'm sure Nylon would be best. This bracket has been designed to mount a piece of 40x20x2 mm aluminium tube. Simply bold down the brackets at each side, place a piece of 1400mm tube between the two sides, drill a hole through the tube using the bracket as a guide, then bolt them down. This seems to allow for a little bit of flex in the chassis and stops and stresses forming. The brackets are angled at 10 degrees to match the curves of the roof. Links for building this in Australia: Good old Bunnings - Grab a snag for me while you're there. Bolts: https://www.bunnings.com.au/pinnacle-m5-x-65mm-stainless-steel-hex-head-bolts-and-nuts-6-pack_p0247307 Aluminium: https://www.bunnings.com.au/metal-mate-40-x-20-x-2mm-x-3m-aluminium-rectangle-tube_p1130547

Compatible Cars

Toyota Land Cruiser

Updated Aug 10, 2026

Originally published on thingiverse.com by Shane Goodwin (ShaneGoodwin501) · License: CC BY

Verified by drivers

Share whether this print actually fits a real car. Installed photos and material notes make the catalog more trustworthy.

Loading fitment proof…

Comments (0)

Part lists

Save this part to named public or private collections. Public lists can be shown on this part page.

Hyundai

4.5K

View & download STL files