Files (6)

cup-holder-base.stl

STL

111.7 KB

cup-holder-LH.stl

STL

91.4 KB

cup-holder-RH.stl

STL

92.4 KB

cup-holder-top.stl

STL

84.6 KB

cup_holder_gps.stl

STL

19.4 KB

cup_holder_top_mt.stl

STL

33.1 KB

Print guidance estimate

Slicer data required

Print cost & setup estimate

Setup guidance plus saved or slicer-confirmed filament, cost, and time. Model file size is never treated as printable volume.

6 model files

Typical selected file

Slice required

Choose the needed variant and slice it; source file size is not printable volume.

Material cost

Slice required

Use the slicer's filament total; STL/3MF byte size is not a cost input.

Print time

Slice required

Slice with the recommended material, infill, orientation, and supports.

STL file	Role	Source size	PETG / ASA 20%	PETG / ASA 25%	100% solid	Recommendation
cup-holder-base.stl	Mount / bracket	111.7 KB STL	Slice file	Slice file	Slice file	Ensure proper orientation in the slicer for optimal printing
cup-holder-LH.stl	Mount / bracket	91.4 KB STL	Slice file	Slice file	Slice file	Ensure proper orientation in the slicer for optimal printing
cup-holder-RH.stl	Mount / bracket	92.4 KB STL	Slice file	Slice file	Slice file	Ensure proper orientation in the slicer for optimal printing
cup-holder-top.stl	Mount / bracket	84.6 KB STL	Slice file	Slice file	Slice file	Ensure proper orientation in the slicer for optimal printing
cup_holder_gps.stl	Mount / bracket	19.4 KB STL	Slice file	Slice file	Slice file	Small functional file: print slowly; consider 80–100% infill for durability.
cup_holder_top_mt.stl	Mount / bracket	33.1 KB STL	Slice file	Slice file	Slice file	Ensure proper orientation in the slicer for optimal printing

Saved setup guidance is used for material, infill, support, and per-file recommendation text; editable numbers are planning estimates only.

Cup Holders

Tacoma Vent Cup Holder

0 downloads67 views0 quality score

Print this part

Check the available model and saved setup details before opening your slicer.

Files

6 hosted model files

STL

Material

PETG or ASA for durability in a car environment

Print time

Slice to calculate

Filament

Slice to calculate

Supports

verify in slicer

Infill

20-30% infill for a balance between weight and strength

Difficulty

Not rated — inspect geometry

Vehicle heat

Cabin/interior use; avoid high-heat zones

Open the STL, 3MF, or OBJ model in your slicer before printing. Confirm orientation, supports, print time, filament use, and printer compatibility. Test-fit before installing it in a vehicle.

License & use

CC BY

Commercial use allowed

Attribution required

The file license permits commercial reuse, subject to any applicable attribution or share-alike terms. License status does not verify vehicle fitment, OEM rights, design patents, or safety.

Shared by

3DPrintedCarPart

Verified

Description

I have a 2015 Toyota Tacoma. It has a cup holder, but I wanted to try to keep my drink cool. I remixed this cup holder to fit my Tacoma, and added some guides on the sides to help direct the air to the drink. I don't have a top cover or a rounded cover for the open back side of the bottle. But it seems to work. Instead of screws I straightened out some paper clips and jammed those through the holes. Printed with my standard ABS setting on my DaVinci Pro. I modified the top holder so it will accept a gps mount. Dual purpose!